久久好色-久久狠-久久黄色毛片-久久黄色网址-亚洲人成图片欧美人成图片-亚洲人成网亚洲欧洲无码

A brief discussion on the application of grinding wheel in stone grinding

2020-08-24 08:21:00

Grinding is a method of cutting workpiece using a grinding wheel as a cutting tool on a grinding machine. The characteristics of this method are as follows:

(1) Because the abrasive particles of the grinding wheel have high hardness and heat resistance, the grinding can process materials with high hardness, such as hardened steel, hard alloy and so on.

(2) The characteristics of grinding wheel and grinding machine determine that the grinding process system can perform even micro-cutting, generally AP =0.001 ~ 0.005mm; High grinding speed, generally up to V =30 ~ 50m/s; Good rigidity of grinding machine; By using hydraulic transmission, grinding can achieve high machining accuracy (IT6 ~ IT5) and small surface roughness (Ra=0.8 ~ 0.2 m) economically. Grinding is one of the main methods of parts finishing.

(3) Due to the intense friction, the grinding area temperature is very high. This can cause stress and deformation and even surface burns on the workpiece. So a lot of coolant must be injected during grinding to reduce grinding temperature. The coolant can also be used for chip removal and lubrication.

(4) Great radial force in grinding. This will cause the machine tool - grinding wheel - workpiece system flexibility, so that the actual cutting depth is less than the nominal cutting depth. Therefore, the grinding will be completed, should not feed polishing, in order to eliminate errors.

(5) After the abrasive obtuse, the grinding force will also increase, resulting in the abrasive grains broken or fell off, re-exposed the sharp edge, this property is called "self-sharpening". Self-sharpening enables grinding to be carried out normally within a certain period of time, but after a certain working time, manual dressing should be carried out to avoid vibration, noise and damage to the surface quality of the workpiece caused by the increase of grinding force.

Grinding wheel

A grinding wheel is a cutting tool for grinding. It is a porous substance bonded by a number of small, hard abrasive particles and a binder. The abrasive particles are directly responsible for the cutting work and must be sharp and have high hardness, heat resistance and certain toughness. Common abrasives are alumina (also known as corundum) and silicon carbide. Alumina abrasive with high hardness and good toughness is suitable for grinding steel. Silicon carbide abrasive with higher hardness, sharper, good thermal conductivity, but more brittle, suitable for grinding cast iron and hard alloy.

The grinding wheel with the same abrasive, due to its different thickness, the surface roughness and processing efficiency of the workpiece after processing are not the same, the coarse abrasive is used for coarse grinding, the fine abrasive is suitable for fine grinding, the coarser abrasive, the smaller particle size.

The binder ACTS as a bond to the abrasive. Ceramic binder is commonly used, followed by resin binder. Different binder selection can affect the corrosion resistance, strength, heat resistance and toughness of grinding wheel.

The hardness of the grinding wheel refers to how hard it is for grinding grains to fall off under the action of external forces. Easy to fall off called soft, vice versa called hard. The hardness of grinding wheel and abrasive are two different concepts. The surface of the workpiece to be ground is soft, and the edge of the abrasive grain (edges and corners) is not easy to wear, so the abrasive grain can be used for a longer time, that is to say, you can choose to stick to a more firm grinding wheel (grinding wheel with higher hardness). On the contrary, the grinding wheel with low hardness is suitable for grinding the workpiece with high hardness.

The grinding wheel works under the condition of high speed. In order to ensure safety, it should be inspected before installation without defects such as cracks. In order to make the grinding wheel work smoothly, a balancing test should be carried out before use.

After working for a certain period of time, the surface gap of the grinding wheel will be blocked by the grinding chips, the sharp Angle of the abrasive will be blunt, and the original geometry will be distorted. It must therefore be trimmed to restore cutting power and correct geometry. The grinding wheel shall be dressed with a diamond pen.

The structure and grinding motion of surface grinding machine

There are many kinds of grinding machines, including surface grinder, cylindrical grinder, internal grinder, universal cylindrical grinder (also grinding internal hole), gear grinder, thread grinder, guide grinder, centerless grinder (grinding external grinder) and tool grinder (grinding tool), etc. The surface grinder and its motion are introduced here.


主站蜘蛛池模板: 国产一区美女视频 | 国产色爽女 | 亚洲国产一区二区三区a毛片 | 亚洲午夜久久久久国产 | 欧美极品第1页专区 | 99久久成人国产精品免费 | 一级毛片无毒不卡直接观看 | 国产一级一级片 | 特黄特黄aaaa级毛片免费看 | 轻点灬大ji巴太粗太长了爽文 | 国产在线精品观看一区 | 四虎影院永久网址 | 在线免费视频观看 | 亚洲视频四区 | 日韩一级在线播放免费观看 | 欧美性色xo影院69 | 色妞视频资源在线观看 | 岛国大片在线播放 | 男女视频免费观看 | 最新亚洲人成网站在线影院 | 亚洲先锋资源 | 99久久免费中文字幕精品 | 日本写真高清视频免费网站网 | 亚洲va久久久噜噜噜久久男同 | 综合色久七七综合七七蜜芽 | 555成人免费影院 | 成年网站在线观看 | 久久综合社区 | 狠狠色噜噜噜噜狠狠狠狠狠狠奇米 | 黄网站色视频免费看无下截 | 亚洲伊人久久大香线蕉影院 | 福利视频免费看 | 女同性进行性行为视频 | xxxxxxxx日本69| 噜噜色综合 | 综合亚洲色图 | 手机看片自拍 | 欧美色婷婷天堂网站 | 欧美乱码视频 | 日本黄色绿像 | 最新激情网站 |