久久好色-久久狠-久久黄色毛片-久久黄色网址-亚洲人成图片欧美人成图片-亚洲人成网亚洲欧洲无码

Superhard wheel grinding requirements for grinding machines

2020-08-24 08:30:00

Super hard wheel grinding, especially high speed grinding, requires good machining stability, low vibration and high linear speed. For example, the PLANOMAT series of surface and form grinding wheels shown on CIMT2001 have a working speed of 170m/s. Therefore, there is a requirement for grinding machine:

(1) Grinding wheel spindle should have high rotary accuracy.

(2) better rigidity of grinding machine, general requirements than ordinary grinding machine about 50% higher, usually should not be less than 100N/ m order of magnitude.

(3) The grinding machine feed system should have high precision, feed speed should be uniform and accurate, longitudinal feed minimum speed should be up to 0.3m/min, transverse feed (cutting depth) should be up to 0.001~0.002mm/ single stroke, in order to ensure the grinding dimension accuracy, geometric shape accuracy and surface roughness.

(4) Each moving parts of the grinding machine, such as the head frame spindle and bearing parts, feed motion guide parts and other parts should be reliable sealing, in order to prevent the super hard abrasive into, accelerate the wear of the parts.

(5) To have a relatively perfect grinding fluid filtration and supply system, the filtration accuracy should be less than 0.5 m.

(6) Each part of the grinding machine should have corresponding anti-vibration and vibration isolation measures, grinding wheel should be fine dynamic balance. 3.4 Dressing of super hard abrasive wheel
Dressing grinding wheel of super hard abrasive is usually divided into two procedures: shaping and sharpening. Shaping is to micro cut the grinding wheel to make it reach the required geometric shape and precision, and make the abrasive tip finely broken to form a micro blade; Sharpening is to remove the binding agent between the grinding particles, so that there is a certain amount of chip space between the grinding particles, and make the grinding particles stand out of the binding agent, forming a cutting edge.

For multi-pore ceramic bonded ultra-hard abrasive wheel (including diamond and CBN wheel), shaping and sharpening can usually be completed at one time due to the loose type of binder. And for the binder for the dense molding sand wheel (such as resin, metal binder), then shaping and sharpening respectively.

The most effective shaping tool for superhard abrasive wheel is diamond dressing tool. Due to wear of dressing tool, the precision of mold surface is often affected by single particle diamond dressing. If diamond wheel dressing is used, the dressing tool can be avoided to wear out too fast, and a better grinding wheel shape can be obtained. The feeding precision of dressing device should be high, and each feed should be controlled in micron level. Excessive dressing will not only affect the grinding quality, but also greatly reduce the service life of the grinding wheel.

There are many ways of sharpening, generally using mechanical method (such as corundum block cutting sharpening, hydraulic jet sharpening) or electrical machining method. The latter is mostly used in the grinding wheel of metal bonding agent. The grinding wheel is used as the anode to remove the metal bonding agent by electric spark or electrolysis. If graphite powder is added to the binder, this method is also suitable for resin and ceramic binder grinding wheels.

In recent years, a rotary diamond cup wheel dressing tool was developed in The University of Tokyo. The mechanism is to make use of the abrasive falling off from the cup wheel to punch the binding bridge between the super hard (diamond or CBN) abrasive grain and the binder, and to produce the squeezing and grinding effect between the abrasive falling off and the super hard wheel to achieve the purpose of dressing. Using this method, no matter for the multi-pore ceramic binder superhard grinding wheel or the dense sand wheel, the shaping and sharpening can be completed in one time. Meanwhile, due to the self-rotation of the cup wheel, the wear is very small, and the shaping force can be almost unchanged during the dressing process, and the value is much smaller than that when dressing with a single particle diamond dressing tool.

主站蜘蛛池模板: 久操免费视频 | 天天躁日日躁狠狠躁一级毛片 | 香港午夜理理伦_级毛片 | 赛罗奥特曼银河帝国普通话免费版 | 性做久久久久久网站 | 天天射天天干天天操 | 又粗又长又大真舒服好爽漫画 | 免费大片a一级一级 | 色综合888 | 婷婷激情四射网 | 狠狠干成人 | 中文天堂最新版www 中文天堂最新版在线精品 中文天堂最新版在线中文 中文天堂最新版资源新版天堂资源 | 99精品国产在热久久 | 国内真实实拍伦视频在线观看 | 天天狠狠 | 日本欧美一区二区三区视频 | 婷婷综合久久中文字幕 | 伊人久久大香线蕉资源 | 九九51精品国产免费看 | 色狠狠网 | 久久精品综合视频 | 看毛片的网站 | 手机看片福利盒子久久青 | 色丁香影院 | 99成人| 男女交性无遮挡免费视频 | 欧美日韩亚洲一区 | 国产高清免费不卡观看 | 久久99久久精品97久久综合 | 四虎影院成人在线观看 | 扒开末成年粉嫩的小缝强文 | 夜色福利| 黑人一区二区三区中文字幕 | 免费大片黄国产在线观看 | 最近2018中文字幕免费看2019 | 午夜男人视频 | 天堂va| 手机看片福利国产 | 色网站免费 | 久久综合五月开心婷婷深深爱 | 35pao强力打造|